Shop Services

Service

Description

Price (Labor)

Brake Lines

Install aftermarket, steel, carbon brake line kits

$105-$136.50

Brake ABS Removal, line install

Install ABS brake line system, or Removal of ABS system and install brake line kit for racing, usually includes pump modification

$420

First Service

Every new bike needs service after the first 600 miles. What this service consists of varies by bike based on manufactures recommendations.

$252-$425, Varies by make/model

Tune Up 1

Change oil and oil filter, check all fluids, inspect and clean air filter, lubricate cables and chain, general inspection of unit

$299

Tune Up 2

Change oil and oil filter, replace spark plugs, check all fluids, inspect and clean air filter, lubricate cables and chain, synchronize carburetors/throttle body, general inspection of unit.

$470

Tune Up 3

Change oil and oil filter, replace spark plugs, check all fluids, inspect and clean air filter, lubricate cables and chain, synchronize carburetors/throttle body, check valve lash clearance, general inspection of unit

$700-$1000

Crash Estimate/Insurance Write Up

We will provide an estimate which includes a breakdown of the cost of individual parts and labor

$105

Power Commander, Bazzaz, Piggyback Fuel Module

Install Dynojet Power Commander PC-V or Bazzaz Zfi/FI management system. Includes on dyno calibration, TPS, Gear, etc.

$220 *most models

Bazzaz Traction Control Unit Install

Install Bazzaz ZfiTC Fuel management with traction control and quick shift. Includes function and setup on dyno. Mapping not included .

$367.50

Exhaust Install

Full System - Price fluxuation varies based on complexity of OEM bodywork removal and installation.

$325-$450

Slip-on / Bolt-on - Side mount exhaust with slip joint at header or catalytic converter.

$115

Sip-on / Under-tail Half system or any slip or bolt on system that has exhaust servo motor cables to remove and/or removal and install of servo bypass adaptor or plug.

$275

Top End Rebuild

Rebuild the top end of a two stroke engine.

$350

Cylinder Head Service

Engine only. Cylinder head removal install and degree cams. For head work only, thinner head gaskets, port polish, valve seat work, etc 

$550-$750

Engine Swap

Removal and install of engine in chassis

$750-$950

Engine Rebuild

Complete disassemble of engine, inspect, rebuild. Superbike engine, Supersport, Overbore, Stroke kits, etc

$950-$1200

Performance Service Prep

Change oil w/ filter with safety wire on oil drain/fill & filter, check and clean or replace air filter, service brake pads & calipers, bleed brake fluid, check battery & charging system, service drive chain, inspect sprockets, inspect steering stem / wheels & wheel bearings, inspect suspension movement, and check torque on critical chassis parts

$400

Safety wire Riding Prep

Drill, safety wire, coolant replacement, prep bike for racing or track day service. Set for WERA tech requirements, other organizations will vary for less strict controls

$472.50- $630

Chassis Service

Service chassis. Swingarm pivot, suspension linkage, steering stem, axles, calipers, flush/bleed brakes, clean air filter and bike. 

$450

Fuel Tank Dry Break

Steel flange (112-001) for IMS female receiver fuel tank modification. Price includes flange, IMS receiver sold separate.

$450

Steering Stem Service

Steering stem bearing replacement

$315

Clutch Replacement

Replace clutch, most slipper clutch / lockup's installation

$288.75

Valve Check

Inspect valve lash clearance.

$650

Oil Change

Change oil and oil filter.

$89.25

Tire Mount and Balance

Wheel on a Sportbike / Naked standard, etc.

$73.50(per wheel)

$90-$130 Front wheel Cruiser & Wing

Rear Wheel on a Cruiser

$100-$125 (Rear price)

Goldwing

$180-$220 (Rear price)