Service

Repair and Maintenance

In addition to our dyno tuning and suspension services,we also offer a full range of repair and maintenance services,including,but not limited to,the following.
Labor prices are set to single service. Combining services and/or parts purchase may decrease individual item service prices.

Please call us at 410-544-5113 or email Kenny  for any questions or detailed pricing information.

Service

Description

Price (Labor)

Brake Lines

Install aftermarket, steel, carbon brake line kits

$100-$130

Brake ABS Removal, line install

Install ABS brake line system, or Removal of ABS system and install brake line kit for racing, usually includes pump modification

$400

First Service

Every new bike needs service after the first 600 miles. What this service consists of varies by bike based on manufactures recommendations.

$240-$405, Varies by make/model

Tune Up 1

Change oil and oil filter, check all fluids, inspect and clean air filter, lubricate cables and chain, general inspection of unit

$260

Tune Up 2

Change oil and oil filter, replace spark plugs, check all fluids, inspect and clean air filter, lubricate cables and chain, synchronize carburetors/throttle body, general inspection of unit.

$400

Tune Up 3

Change oil and oil filter, replace spark plugs, check all fluids, inspect and clean air filter, lubricate cables and chain, synchronize carburetors/throttle body, check valve lash clearance, general inspection of unit

$590

Crash Estimate/Insurance Write Up

We will provide an estimate which includes a breakdown of the cost of individual parts and labor

$100

Power Commander, Bazzaz, Piggyback Fuel Module

Install Dynojet Power Commander PC-V or Bazzaz Zfi/FI management system. Includes on dyno calibration, TPS, Gear, etc.

$220 *most models

Bazzaz Traction Control Unit Install

Install Bazzaz ZfiTC Fuel management with traction control and quick shift. Includes function and setup on dyno. Mapping not included .

$350

Exhaust Install

Full System - Price fluxuation varies based on complexity of OEM bodywork removal and installation.

$300-$400

Slip-on / Bolt-on - Side mount exhaust with slip joint at header or catalytic converter.

$100

Sip-on / Undertail Half system or any slip or bolt on system that has exhaust servo motor cables to remove and/or removal and install of servo bypass adaptor or plug.

$250

Top End Rebuild

Rebuild the top end of a two stroke engine.

$320

Cylinder Head Service

Engine only. Cylinder head removal install and degree cams. For head work only, thinner head gaskets, port polish, valve seat work, etc 

$550-$650

Engine Swap

Removal and install of engine in chassie

$700-$850

Engine Rebuild

Complete disassemble of engine, inspect, rebuild. Superbike engine, Supersport, Overbore, Stroke kits, etc

$950-$1200

Nitrous Dry System

 Install nitrous dry system, from basic WOT (wide open throttle) switch, to multi stage nitrous controllers. 

$475-$600

Race Trackday Prep

Drill, saftey wire, coolant replacement, prep bike for racing or track day service. Set for WERA tech requirements, other organizations will varry for less strict controls

$450 - $600

Race Chassie Service

Service chassie. Swingarm pivot, suspension linkage, steering stem, axles, calipers, flush/bleed brakes, clean air filter and bike. 

$400

Fuel Tank Dry Break

Steel flange (112-001) for IMS female receiver fuel tank modification. Price includes flange, IMS receiver sold separate.

  • IMS DRY BREAK RECEIVER INSTALLED 1 IMS DRY BREAK RECEIVER INSTALLED 2 IMS DRY BREAK RECEIVER INSTALLED 3 
  • (Click Images for larger version)

$450

Steering Stem Service

Steering stem bearing replacement

$300

Clean Carburetor

Remove, disassemble, clean, assemble, re-install, balance/synchronize

Single/Twin Cylinder

$300 

Three or more carburetor per cylinder. Remove, disassemble, clean, assemble, re-install, balance/synchronize

$450

Chain and Sprocket Install

Remove and install front/rear sprockets and drive chain.

$160 -$250

Clutch Replacement

Replace clutch, most slipper clutch / lockup's installation

$275

Valve Check

Inspect valve lash clearance.

$540

Oil Change

Change oil and oil filter.

$85

Jet Kit Install

Installation of jet kit for a four cylinder engine

$450

Welding

TIG/MIG for aluminum, steel, and stainless steel.

$75 per hour

Tire Mount and Balance

Wheel on a Sportbike / Naked standard, etc.

$63 (per wheel. Front Cruiser & Wing)

Rear Wheel on a Cruiser

$95-$112.5 (Rear price)

Goldwing

$150-$200 (Rear price)